简体中文
English
Spanish
Product 
1. Product application scope:
It can be used to understand the composition of the water spray chamber and *r surface cooler, deepen the difference between the performance of direct contact and surface heat and moisture exchange equipment through experiments, master the methods of measuring the temperature, relative humidity and resistance characteristics of the water spray chamber and surface cooler; be familiar with the determination methods of heat exchange, heat exchange efficiency coefficient and contact coefficient.
2. Product use working environment:
2.1 Working environment temperature: 0-40℃.
2.2 Working environment humidity: < 80% (no condensation).
2.3 Power supply: single-phase 220V, 50 Hz.
3. Technical and performance parameters:
3.1 Cold water system: compressor, condenser, evaporator coil, high-pressure water pump, flow meter, water spray chamber, nozzle, surface cooler, constant temperature room, low-noise fan, humidifier, electric heater.
3.2 Measurement and control system: temperature control instrument, temperature measuring instrument, digital current and voltage meter, micro pressure meter, flute tube).
3.3 Other parameters
*r duct cross-sectional dimensions: 250*250mm
Compressor: 1000W, cooling capacity 2730W Brand: Hitachi 1.5P
Water pump: self-priming jet pump, Q=4.2m3/h, H=35m, N= 370W, voltage 220V, 50Hz
Centrifugal fan: motor power 750W Voltage 220V *r volume 2850m3/h Full pressure 490Pa Speed 1400r/m Low noise fan
Refrigerant: R22
Flow meter: rotor flow meter caliber DN15, flow range 40-400L/h
3.4 Single chip microcomputer , PLC programmable design and control virtual simulation software:
This software is developed based on Unity3D, with built-in experimental steps, experimental instructions, circuit diagrams, component lists, connection lines, power on, circuit diagrams, scene reset, return and other buttons. After the connection and code are correct, the 3D machine model can be operated through the start/stop, forward motion, and reverse motion buttons . When the line is connected, the 3D machine model can be enlarged/reduced and translated.
1. Relay control: Read the experimental instructions and enter the experiment. By reading the circuit diagram, select relays, thermal relays, switches and other components in the component list and drag and drop them into the electrical cabinet. The limiter is placed on the 3D machine model. You can choose to cover the lid. Some component names can be renamed. Then click the connection line button to connect the terminals to the terminals. After the machine circuit is successfully connected, choose to turn on the power and operate. If the component or line connection is wrong, an error box will pop up, and the scene can be reset at any time.
2. PLC control: The experiment is the same as relay control, with the addition of PLC control function. After the connection is completed, press the PLC coding button to enter the program writing interface, and write two programs, forward and reverse. There are 12 ladder diagram symbols in total. After writing, select Submit to verify the program. After successful verification, turn on the power to operate. Error boxes will pop up for components, line connections, and code errors, and the scene can be reset at any time.
3. MCU control: The experiment is the same as relay control, with the addition of MCU control function. After the connection is completed, press the C coding button to enter the programming interface, enter the correct C language code, and submit for successful verification. Turn on the power to operate. Error boxes will pop up for components, line connections, and code errors, and the scene can be reset at any time.
4. System configuration list
欢迎咨询YLLR-BLQ Surface Cooler Performance Experimental Platform相关问题,我们是源头工厂，有标准工业厂房生产基地，欢迎前来考察，如有YLLR-BLQ Surface Cooler Performance Experimental Platform其他问题，可联系19957812178
It can be used to understand the composition of the water spray chamber and *r surface cooler, deepen the difference between the performance of direct contact and surface heat and moisture exchange equipment through experiments, master the methods of measuring the temperature, relative humidity and resistance characteristics of the water spray chamber and surface cooler; be familiar with the determination methods of heat exchange, heat exchange efficiency coefficient and contact coefficient.
2. Product use working environment:
2.1 Working environment temperature: 0-40℃.
2.2 Working environment humidity: < 80% (no condensation).
2.3 Power supply: single-phase 220V, 50 Hz.
3. Technical and performance parameters:
3.1 Cold water system: compressor, condenser, evaporator coil, high-pressure water pump, flow meter, water spray chamber, nozzle, surface cooler, constant temperature room, low-noise fan, humidifier, electric heater.
3.2 Measurement and control system: temperature control instrument, temperature measuring instrument, digital current and voltage meter, micro pressure meter, flute tube).
3.3 Other parameters
*r duct cross-sectional dimensions: 250*250mm
Compressor: 1000W, cooling capacity 2730W Brand: Hitachi 1.5P
Water pump: self-priming jet pump, Q=4.2m3/h, H=35m, N= 370W, voltage 220V, 50Hz
Centrifugal fan: motor power 750W Voltage 220V *r volume 2850m3/h Full pressure 490Pa Speed 1400r/m Low noise fan
Refrigerant: R22
Flow meter: rotor flow meter caliber DN15, flow range 40-400L/h
3.4 Single chip microcomputer , PLC programmable design and control virtual simulation software:
This software is developed based on Unity3D, with built-in experimental steps, experimental instructions, circuit diagrams, component lists, connection lines, power on, circuit diagrams, scene reset, return and other buttons. After the connection and code are correct, the 3D machine model can be operated through the start/stop, forward motion, and reverse motion buttons . When the line is connected, the 3D machine model can be enlarged/reduced and translated.
1. Relay control: Read the experimental instructions and enter the experiment. By reading the circuit diagram, select relays, thermal relays, switches and other components in the component list and drag and drop them into the electrical cabinet. The limiter is placed on the 3D machine model. You can choose to cover the lid. Some component names can be renamed. Then click the connection line button to connect the terminals to the terminals. After the machine circuit is successfully connected, choose to turn on the power and operate. If the component or line connection is wrong, an error box will pop up, and the scene can be reset at any time.
2. PLC control: The experiment is the same as relay control, with the addition of PLC control function. After the connection is completed, press the PLC coding button to enter the program writing interface, and write two programs, forward and reverse. There are 12 ladder diagram symbols in total. After writing, select Submit to verify the program. After successful verification, turn on the power to operate. Error boxes will pop up for components, line connections, and code errors, and the scene can be reset at any time.
3. MCU control: The experiment is the same as relay control, with the addition of MCU control function. After the connection is completed, press the C coding button to enter the programming interface, enter the correct C language code, and submit for successful verification. Turn on the power to operate. Error boxes will pop up for components, line connections, and code errors, and the scene can be reset at any time.
4. System configuration list
| Serial number | name | Specifications | quantity |
| 1 | Surface cooling section | 1 set | |
| 2 | Spray Room | 1 set | |
| 3 | Constant temperature room | 1 set | |
| 4 | Fan | CF-11 | 1 set |
| 5 | Refrigeration Compressors | 12M2 | 1 set |
| 7 | Vertical liquid reservoir | 1HP | 1 |
| 8 | Coil evaporator | 1 set | |
| 9 | St*nless steel water pump | 370W | 1 set |
| 10 | Flow Meter | LZB-15 | 1 |
| 11 | humidifier | GO-2028 | 1 set |
| 12 | Measurement and control systems | 1 set |
欢迎咨询YLLR-BLQ Surface Cooler Performance Experimental Platform相关问题,我们是源头工厂，有标准工业厂房生产基地，欢迎前来考察，如有YLLR-BLQ Surface Cooler Performance Experimental Platform其他问题，可联系19957812178
